% Template for IGARSS-2010 paper; to be used with:
%          spconf.sty  - LaTeX style file, and
%          IEEEbib.bst - IEEE bibliography style file.
% --------------------------------------------------------------------------
\documentclass{article}
\usepackage{spconf,amsmath,epsfig}

% Example definitions.
% --------------------
\def\x{{\mathbf x}}
\def\L{{\cal L}}

% Title.
% ------
\title{AUTHOR GUIDELINES FOR IGARSS 2011 ABSTRACTS}
%
% Single address.
% ---------------
\name{Author(s) Name(s)\thanks{Thanks to XYZ agency for funding.}}
\address{Author Affiliation(s)}
%
% For example:
% ------------
%\address{School\\
%	Department\\
%	Address}
%
% Two addresses (uncomment and modify for two-address case).
% ----------------------------------------------------------
%\twoauthors
%  {A. Author-one, B. Author-two\sthanks{Thanks to XYZ agency for funding.}}
%	{School A-B\\
%	Department A-B\\
%	Address A-B}
%  {C. Author-three, D. Author-four\sthanks{The fourth author performed the work
%	while at ...}}
%	{School C-D\\
%	Department C-D\\
%	Address C-D}
%
\usepackage{setspace}
%\singlespacing
\onehalfspacing
%\doublespacing
%\setstretch{1.1}
\begin{document}
\onecolumn
%\ninept
%
\maketitle
%
\section{Introduction}
\label{sec:intro}

These guidelines include complete descriptions of the fonts, spacing, and
related information for producing your abstracts. It is suggested to follow
them and if you have any questions, direct them to Conference Management
Services, Inc.: Phone +1-979-846-6800 or Fax +1-979-846-6900 or email to
papers@igarss11.org.

\section{Formatting your paper}
\label{sec:format}

All printed material, including text, illustrations, and charts, must be kept
within a print area of 7 inches (178 mm) wide by 9 inches (229 mm) high. Do not
write or print anything outside the print area. The top margin should be 1 inch
(25 mm).

\section{PAGE TITLE SECTION}
\label{sec:pagestyle}

The paper title (on the first page) should begin 1.38 inches (35 mm) from the
top edge of the page, centered, completely capitalized, and in Times 14-point,
boldface type.  The authors' name(s) and affiliation(s) appear below the title
in capital and lower case letters.  Papers with multiple authors and
affiliations may require two or more lines for this information.

\section{TYPE-STYLE AND FONTS}
\label{sec:typestyle}

In nine point type font, capital letters are 2 mm high.  If you use the
smallest point size, there should be no more than 3.2 lines/cm (8 lines/inch)
vertically.  This is a minimum spacing; 2.75 lines/cm (7 lines/inch) will make
the paper much more readable.  Larger type sizes require correspondingly larger
vertical spacing.  Please do not double-space your paper.  True-Type 1 fonts
are preferred.

\section{MAJOR HEADINGS}
\label{sec:majhead}

Major headings, for example, "1. Introduction", should appear in all capital
letters, bold face if possible, centered in the column, with one blank line
before, and one blank line after. Use a period (".") after the heading number,
not a colon.

\subsection{Subheadings}
\label{ssec:subhead}

Subheadings should appear in lower case (initial word capitalized) in
boldface.  They should start at the left margin on a separate line.
 
\subsubsection{Sub-subheadings}
\label{sssec:subsubhead}

Sub-subheadings, as in this paragraph, are discouraged. However, if you
must use them, they should appear in lower case (initial word
capitalized) and start at the left margin on a separate line, with paragraph
text beginning on the following line.  They should be in italics.

\section{PRINTING YOUR PAPER}
\label{sec:print}

Print your properly formatted text on high-quality, 8.5 x 11-inch white printer
paper. A4 paper is also acceptable, but please leave the extra 0.5 inch (12 mm)
empty at the BOTTOM of the page and follow the top and left margins as
specified.

\section{PAGE NUMBERING}
\label{sec:page}

Please do {\bf not} paginate your paper.  Page numbers, session numbers, and
conference identification will be inserted when the paper is included in the
proceedings.

\section{ILLUSTRATIONS, GRAPHS, AND PHOTOGRAPHS}
\label{sec:illust}

Illustrations must appear within the designated margins. If possible, position
illustrations at the top of page, rather than in the middle or at the bottom.
Caption and number every illustration.  All halftone illustrations must be
clear black and white prints. Color may be used, but it should be clear when
printed on a black-only printer.

Since there are many ways, often incompatible, of including images (e.g., with
experimental results) in a LaTeX document, below is an example of how to do
this \cite{Lamp86}.

% Below is an example of how to insert images. Delete the ``\vspace'' line,
% uncomment the preceding line ``\centerline...'' and replace ``imageX.ps''
% with a suitable PostScript file name.
% -------------------------------------------------------------------------
\begin{figure}[htb]

\begin{minipage}[b]{1.0\linewidth}
  \centering
% \centerline{\epsfig{figure=image1.ps,width=8.5cm}}
  \vspace{2.0cm}
  \centerline{(a) Result 1}\medskip
\end{minipage}
%
\begin{minipage}[b]{.48\linewidth}
  \centering
% \centerline{\epsfig{figure=image3.ps,width=4.0cm}}
  \vspace{1.5cm}
  \centerline{(b) Results 3}\medskip
\end{minipage}
\hfill
\begin{minipage}[b]{0.48\linewidth}
  \centering
% \centerline{\epsfig{figure=image4.ps,width=4.0cm}}
  \vspace{1.5cm}
  \centerline{(c) Result 4}\medskip
\end{minipage}
%
\caption{Example of placing a figure with experimental results.}
\label{fig:res}
%
\end{figure}

\section{COPYRIGHT FORMS}
\label{sec:copyright}

You must send your fully completed, signed IEEE copyright release form when you
submit your paper. We {\bf must} have this form before your paper can be sent
to reviewers.  The copyright form is available as a PDF file on the conference
website.

\section{REFERENCES}
\label{sec:ref}

List and number all bibliographical references at the end of the paper.  The references can be numbered in alphabetic order or in order of appearance in the document.  When referring to them in the text, type the corresponding reference number in square brackets as shown at the end of this sentence \cite{C2}.

% References should be produced using the bibtex program from suitable
% BiBTeX files (here: strings, refs, manuals). The IEEEbib.bst bibliography
% style file from IEEE produces unsorted bibliography list.
% -------------------------------------------------------------------------
\bibliographystyle{IEEEbib}
\bibliography{strings,refs}

\end{document}
